
Cryogenic mold removal that kills spores without water or chemicals
Dry Ice Blasting Mold in NEWBURY PARK, California
Dry Ice Blasting Mold in NEWBURY PARK, California strips mold off structural framing, sheathing and joists using frozen CO2 pellets instead of sand, soda or water. If you own a Dos Vientos or Old Newbury Park home with attic mold after a roof leak, or a crawl space that smells musty year-round, this is the cleanest way to get the surface back to bare wood. We inspect, blast, and verify before we leave.
What's included
What Our Dry Ice Blasting Mold Service Includes
Every job includes inspection, containment, blasting, HEPA vacuum, antimicrobial treatment and post-remediation testing. Add-ons like vapor barrier installation, duct cleaning and fogging treatment are quoted separately based on what your inspection finds.
Full Inspection and Moisture Mapping
Thermal imaging camera and moisture meter readings on every affected surface, plus boroscope inspection camera in wall cavities. You get photos and a written scope before we start.
Containment and Negative Air
6-mil poly containment with zipper doors, negative air machine and air scrubber running throughout. HVAC registers sealed to keep spores out of living space.
Dry Ice Blasting of Affected Surfaces
Framing, sheathing, joists, subfloor and block walls blasted at 100 to 150 PSI. Pressure adjusted down for soft or historic lumber. Includes all dry ice consumed on the job.
HEPA Vacuum and Antimicrobial
Full HEPA vacuum of every surface after blasting, followed by antimicrobial solution on porous wood. We use Concrobium or Benefect depending on the substrate and your sensitivity.
Post-Remediation Mold Testing
Air samples and surface lifts compared to outdoor baseline. Written clearance report suitable for insurance claims and real estate disclosure.
Debris Removal and Final Clean
All bagged debris removed from site, containment taken down, and work area wiped down. We leave the space ready for re-occupancy, usually within 24 hours of clearance.
Service overview
What Dry Ice Blasting Mold in NEWBURY PARK, California Actually Does
Dry Ice Blasting Mold in NEWBURY PARK, California is a cryogenic remediation method that fires rice-sized dry ice pellets at 300 to 500 feet per second to lift mold, spores and surface staining off wood, block and metal. The pellets hit at roughly -109 degrees Fahrenheit, flash-freezing the mold and causing it to crack and release from the substrate. There is no water, no sand, no soda and no chemical residue left behind. The CO2 sublimates on contact and disappears, so the only thing we vacuum up is the mold itself.
Local demand here is real. Newbury Park sits in a coastal-influenced pocket of Ventura County where morning marine layer keeps attic and crawl space humidity high well into spring. We see hidden mold behind drywall after a slow supply-line drip, black mold on bathroom ceilings in Ventu Park condos, and crawl space mold growth under 1960s raised-foundation homes. If you have been searching for dry ice mold removal near me NEWBURY PARK CA after a water damage event, this is the service that gets framing back to clean wood without tearing the house apart.
The service timeline
Our Dry Ice Blasting Mold Process, Step by Step
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and Mapping
We start with a thermal imaging camera and a moisture meter to find the actual moisture source, then run a boroscope inspection camera into wall cavities and rim joists. You get photos of every affected area and a written scope. This stage usually takes 60 to 90 minutes on a single-family home.
Containment and Air Control
We build 6-mil poly containment around the work zone and set up a negative air machine with HEPA filters so spores cannot migrate into living space. An air scrubber runs continuously. On occupied homes we seal HVAC registers and run a separate scrubber in the adjacent room to protect air quality.
Dry Ice Blasting
Our technician suits up in personal protective equipment and runs the dry ice blasting machine at 100 to 150 PSI, working top-down and corner-out. A 500 square foot attic typically takes three to five hours. The CO2 pellets sublimate on impact, so there is no media pile to shovel out afterward.
HEPA Vacuum and Antimicrobial
Once blasting is done, we HEPA vacuum every surface, then apply an antimicrobial solution to porous wood and any remaining staining. On crawl spaces we install a vapor barrier and seal penetrations with caulk and sealant. This stage runs two to four hours depending on square footage.
Verification and Clearance
We run post-remediation mold testing with air samples and surface lifts, then compare results to the outdoor baseline. You get a written clearance report suitable for a real estate transaction or insurance claim. If numbers do not clear, we re-blast at no additional cost.
Tools & methods
Tools and Methods We Use for Cryogenic Mold Cleaning
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Dry Ice Blasting Machine
Fires rice-sized CO2 pellets at 100 to 150 PSI to lift mold off framing, sheathing and block. Adjustable pressure for soft or historic lumber.
Thermal Imaging Camera
Finds temperature differentials that reveal hidden moisture behind drywall and in ceiling cavities before we open anything up.
Moisture Meter
Confirms active moisture in wood and drywall so we know what is colonized versus what is just stained.
Boroscope Inspection Camera
Lets us see inside wall cavities, rim joists and duct plenums through a small inspection hole.
Negative Air Machine and Air Scrubber
Maintains negative pressure inside containment and filters airborne spores through HEPA filters so they do not migrate into living space.
HEPA Vacuum
Captures mold dust and debris after blasting. Every surface gets vacuumed before we apply antimicrobial.
Fogging Machine
Delivers antimicrobial and odor treatment into duct interiors and tight cavities that blasting cannot reach.
Use cases
When to Call for Dry Ice Blasting Mold
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl Space Joists Under a 1965 Ranch
An Old Newbury Park home had visible white and black growth on floor joists and the subfloor across a 600 square foot crawl space. The house smelled musty year-round and the owner had been quoted for full joist replacement. → We blasted the joists, rim and subfloor in two days, HEPA vacuumed, applied antimicrobial, and installed a reinforced vapor barrier. Moisture readings on the joists dropped from 22 percent to 11 percent. Clearance testing confirmed the spore count was back to baseline.
Bathroom Ceiling in a Ventu Park Condo
A condo owner had recurring black mold on the bathroom ceiling that came back within months of every repaint. The exhaust fan was undersized and a slow supply-line leak had colonized the ceiling joists above the drywall. → We removed the affected drywall, blasted the ceiling joists, applied antimicrobial, and reinstalled mold-resistant board. We also upgraded the exhaust fan to a properly sized unit. Clearance samples came back clean, and the ceiling has stayed mold-free through two full winters.
Problems we solve
Mold Problems We Solve With Dry Ice Blasting
Most Newbury Park mold calls fall into a handful of patterns. Here is what we see and how blasting solves it without tearing your house apart.
Hidden mold behind drywall after a slow leak
We locate the leak with a thermal imaging camera, open a small inspection port, and blast the framing through the cavity. Insulation gets replaced, drywall gets patched, and you avoid a full wall tear-out. Most jobs close in one day.
Black mold on bathroom ceiling in a condo
We blast the ceiling framing and joists after removing the affected drywall, apply antimicrobial, and re-install with mold-resistant board. We also check the exhaust fan CFM and recommend an upgrade if it is undersized.
Crawl space mold growth under a raised foundation
We blast the joists, rim and subfloor, then install a vapor barrier and seal penetrations with caulk and sealant. That cuts the moisture source and stops regrowth. Most crawl spaces are done in one to two days.
Attic mold after roof leak
We blast the sheathing and rafters back to bare wood, apply antimicrobial, and verify clearance with air samples. If the leak is still active, we coordinate with your roofer before blasting so the fix holds.
Pricing process
Dry Ice Blasting Mold Pricing in Newbury Park
$1,200 - $6,500 depending on scope, with most residential jobs landing between $2,400 and $3,800
Square footage affected
Blasting is priced per square foot of contaminated surface. A 200 square foot bathroom is a very different job than a 1,500 square foot attic. We measure during inspection and quote the actual number.
Access difficulty
Tight attics in Dos Vientos and shallow crawl spaces in Reino take more time and more dry ice. If we need to cut additional access panels, that adds labor and patching.
Dry ice consumption
Heavy or deeply embedded growth burns through more pellets. A typical attic job uses 150 to 300 pounds of dry ice, and the material cost is passed through at our cost, not marked up.
How much does Dry Ice Blasting Mold cost in NEWBURY PARK California?
Most residential jobs run $1,800 to $6,500 in 2026, with a typical single attic or crawl space landing around $2,400 to $3,800. Price depends on square footage, access difficulty, whether containment is needed, and how much dry ice the job consumes. Small bathroom or closet jobs can come in under $1,200. We give you a written number before we start, and we do not add line items mid-job.
Is CO2 blasting mold removal safe for wood in NEWBURY PARK?
Yes. Dry ice blasting is one of the gentlest methods for wood framing because the pellets do not cut or pit the surface the way sand or soda can. The CO2 sublimates on impact, so there is no moisture left behind to swell the wood or feed new growth. On soft or historic lumber we dial the pressure down to 60 to 80 PSI and test a small area first. We have blasted 100-year-old Douglas fir in Old Newbury Park without surface damage.
How does dry ice blasting compare to traditional mold removal in NEWBURY PARK California?
Traditional removal means wire brushing, sanding, or cutting out drywall and framing, then drying the area for three to five days. Dry ice blasting cleans the same framing in one to two days with no water and no media to dispose of. It reaches tighter cavities than hand tools, and it does not spread spores the way dry sanding can. The trade-off is equipment cost, which is why not every contractor offers it.
Who offers CO2 blasting mold removal near me in NEWBURY PARK?
We do. Mold Remediation Service Newbury Park runs a dedicated dry ice blasting rig and covers every Newbury Park neighborhood, including Rancho Conejo, Dos Vientos, Pepper Tree, Ventu Park and Conejo Oaks. We also serve surrounding Ventura County communities. Call (833) 929-5837 for a same-day inspection, or book online and we will confirm a two-hour arrival window.
Ready when you are
Get Dry Ice Blasting Mold in NEWBURY PARK, California Today
Call (833) 929-5837 and talk to a technician who can quote your job over the phone. We answer 24/7, dispatch same-day for emergencies, and give you a written scope before any work starts. Licensed, insured and bonded through the California Contractors State License Board.

Talk with the local team
Request Dry Ice Blasting Mold
Call us at (833) 929-5837 any time, day or night. We answer the phone 24/7 and can usually schedule an inspection the same day. If you prefer email, send photos of the affected area to info@moldremediationservicenewburypark.com and we will get back to you within a few hours.



